#
# Example Configuration File for PCDig Module
# Camera: Kodak Megaplus ES 4.0
#
# Matthias Stein 05/00
#

# This works with the following camera setup:
# STS?    - ask for status
# ADJ 0
# BNS 1   - no binning
# DEF ON
# DGN 1
# FSH OF
# FRS 8   - 8 frames
# MDE CD  - controlled mode
# RDM 1   - single channel
# SMC OF
# SMB 33
# SMT 33
# STP N
# TPD 5.0
# TPW 12 
# TRM P   - positive polarity
# TRS AIA - trigger via AIA connector
 

[PCD:0]			# Board 0

      CAMERA_NAME = "Kodak Megaplus ES 4.0 fps:8 (8bit)"
      EXO_FILENAME = "p1b1tp00.exo"
      LEN_SYNC = ASYNC
      LEN_POLARITY = RISING_EDGE
      FEN_ENABLE = ENABLE
      FEN_POLARITY = RISING_EDGE
      MULTI_ENABLE = DISABLE
      MULTI_POLARITY = ACTIVE_HIGH
      MULTI_INPUT_MODE = MULTI_INPUT_FIELD
#     PCLK_POLARITY = FALLING_EDGE		# read only register
#     MULTI_OUTPUT_ENABLE = DISABLE		# this is not configurable
#     USE_EXT_MULTI = DISABLE			# this is not configurable
      RETIME_ENABLE = DISABLE
      RETIME_POLARITY = RISING_EDGE
      CAM3_ENABLE = DISABLE
      EXSYNC_ENABLE = ENABLE
      EXSYNC_POLARITY = ACTIVE_LOW
      EXSYNC_MODE = EXSYNC_FREE_RUNNING
      PRI_ENABLE = ENABLE
      PRI_POLARITY = ACTIVE_LOW
      CAM_MODE_CTL = 0
      CCLK_STATIC_ENABLE = ENABLE
      CCLK_STATIC_STATE = LEVEL_HIGH
#     EXT_SYNC_TIME = 572.000			# us (140ns ... 572us)
      # default exposure time !!!
      EXT_SYNC_PERIOD_TIME = 40000.000		# us (210ns ... 18.75s)
      # default readout time !!!
      EXSYNC_MIDPOINT_DELAY = 120000.000	# us (210ns ... 18.75s)
      # this controls the same as the above value (readout time)
      # the last value is the important (overwrites the first)
      PRI_MIDPOINT_DELAY = 120000.000		# us (210ns ... 18.75s)
      EXSYNC_START_LOCATION = EXSYNC_START_CYCLE_END
      PRI_START_LOCATION = PRI_START_CYCLE_END
      PRI_END_LOCATION = PRI_END_IS_START_DEPEND
      HORZ_OFF = 0
      WIDTH_PIXELS = 2048
      VERT_OFF = 0
      HEIGHT_PIXELS = 2048
      CCLK_FREQ_SEL = 15.000000			# MHz (320kHz ... 100MHz)
      PIXEL_SIZE = 8
      TRIGGER_POLARITY = FALLING_EDGE,FALLING_EDGE
      TRIGGER_SRC = TTL_TRIG,TTL_TRIG
      TRIG_GLITCH_DETECTOR = DISABLE,DISABLE
#     TRIGGER_STATE = LEVEL_HIGH,LEVEL_LOW	# read only register
#     GEN_SW_TRIGGER = 2118125364,2118125364	# this is not configurable
      TRIG_DIVIDE_FACTOR = 256
      TRIG_DIVIDE_CONTROL = DISABLE_TRIG_DIVIDE
#     PARAM_GROUPS_APPLICABLE = 14
      IMAGE_GEOMETRY = 1CHAN_L2R		# 2CHAN_INTERLEAVED
#     NUM_CAMERAS = 1